Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя

Страница: 39 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

Outdoor and Wash Down Installations

Tritex ratings: The T2M 090/ 115 with the P5 option and the T2X

90/115, R2M/G 090/115 have been tested to IP 65. The electronic

enclosure as tested by UL as a Type 4 enclosure rating if NPT

connection ports are used. Tritex actuators are not intended for

applications where the actuator could possibly be submerged.

1. Avoid rod/shaft up installations if possible; if not possible, make

external provisions to keep rod/shaft exposure to water to a

minimum. When new, the seals are effective to IP 65 or better.

However, over time, depending on the amount of side load, they

can wear and eventually allow moisture to ingress. Contact Exlar

application engineering for special options.

2. With the NPT connection option, use thread sealant or Teflon

tape on the connector/conduit threads

3. If straight metric conduit connection is used, verify the

connector/fitting IP rating and verify the connector O-ring is

in place.

4. If cord-grip type cable glands are used, the type with soft rubber

glands are preferred (IP 68). The firmer rubber can cause the

cable to compress over time, compromising the seal between the

gland and the cable. Cable strain reliefs should also be

considered to assure tension, bending radius or flexing of the

cable over time does not compromise the seal. Careful

consideration and testing is required when these glands are

used in outdoor applications.

5. If the I connector option is used verify the connector plugs are

properly sealed and have the desired

IP rating. During installation, be sure

to screw the plug all the way on to the

receptacle for proper sealing.

6. If possible, position conduit fittings or

loop cable / flexible conduit so water

does not drain towards the conduit

fitting. When the wire termination

cover is re-installed, verify the O-ring gasket is in place and the

surfaces of the O-ring as well as the cover are free from debris

so a good seal can be achieved. If the O-ring is missing replace

it with PN

–

46896

7. When re-installing the termination cover, tighten all 4 screws

evenly to be sure the cover seats flat. Tighten the screws to

assure the cover is securely held against the O-ring/gasket.

Caution, over tightening can strip the threads in the enclosure. If

any screws are missing replace them with Exlar PN 64746

(M3x0.5 x 8mm stainless)

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды