Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя

Страница: 32 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

General Operation

The Tritex Series of actuators and motors function in the same manner

as a brushless servomotor. The servo amplifier is used to rotate the

motor at controlled speed and torque, and for controlled numbers of

revolutions and move times. This rotary motion is translated into linear

motion by the internal planetary roller screw mechanism of the T2M /

T2X Series linear actuator.

The rotary motion of the motor and the linear motion of the actuator

correspond to the following relationships:

Linear Distance Traveled (in)

= (Motor Revolutions)*

(Roller Screw Lead)

Linear Speed (in/sec)

= ((Motor RPM) / 60)*(Roller Screw Lead)

Linear Force (lbf)

= ((Motor Torque (in-lbf))*(2

)*(efficiency)) /

(Roller Screw Lead (in))

All of the above relationships require proper anti-rotation of the T2M

Series actuator rod.

Mounting Configurations

The standard configurations available are Rear Clevis, Side Mount,

Side Trunion and Front Flange (See Model Mask and ordering guide in

the General Specifications section). Mounting dimensional drawings in

the following pages:

T2M Series Linear Actuator Anti-rotation Option

The unique design of the T2M Series linear actuators allows the

extending rod to rotate. This simplifies the setup of the actuator by

allowing the user to rotate the rod and thread it in and out of the actuator

for mechanical attachment or system testing.

This feature also requires that the rod be kept from rotating when used

in its dedicated application to insure proper linear motion. In most

applications, such as those where the load is coupled to linear bearings

or some other support device, the load cannot rotate, providing anti-

rotation for the extending rod of the actuator.

For applications in which the load is free to rotate, Exlar offers the anti-

rotation systems shown in drawings following the mounting dimension

drawings. The drawings show the rod and bushing on only one side of

the actuator. For long stroke actuators, the rod and bushing are require

on both sides of the actuator.

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды