Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя страница 8

Страница: 8 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

If connected by plug and socket

A special hazard may exist where the actuator is

incorporated into a system connected to the AC supply by

a plug and socket. The pins of the plug are not generally isolated from

the charge stored in the bus capacitor, so must be considered electrically

“hot” until the discharge time has expired. It is the responsibility of the

user to avoid any possibility of electric shock from the pins when they are

accessible.

Grounding - High Leakage Current

The drive must be grounded by a conductor sufficient to

carry all possible fault current in the event of a fault. This

equipment has high earth leakage current. You must comply with local

safety regulations with respect to minimum size and special installation

requirements on the protective earth conductor for high leakage current

equipment. The instructions for ground connections shown in this manual

must be followed.

Compatibility with Residual Current-operated

Protection Device (RCD)

This product can cause a DC current in the protective

earthing conductor. Where a residual current –operated protective (RCD)

or monitoring (RCM) device is used for protection in case of direct or

indirect contact, only an RCD or RCM of Type B is allowed on the supply

side of this product.

Hot Surface – Risk of Burn.

Exposed surfaces of the actuator may exceed 70 degrees

C under normal operation and can take a long time to cool,

resulting in a risk of burns when touched.

WARNING

CAUTION

WARNING

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды