Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя

Страница: 54 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

Power Connector Wiring

Refer to the following table for standard pre-wired power connector,

part of Option “I”.

Wiring for “I” option - M23 power connector

Function Pin

Internal

wire color

Cable wire

color

Function Pin

Internal

wire color

Cable wire

color

Black

Brown

Red

Orange

Black

Blue

White

Drain/

Coupling

n/c

Drain

Green

Grn/Yel

Note: See Cable section for cable details

Over Temperature Protection

UL approved motor over temperature sensing is not provided by

the drive.

The motor contains a UL recognized temperature sensor embedded in

the stator windings which opens when the stator temperature reaches

130

⁰

C. This sensor is permanently connected to the Tritex drive and will

generate an Actuator Overtemperature fault.

The drive also provides motor over temperature protection by limiting

the continuous current to the motor. The continuous current limits are set

at the factory and cannot be adjusted. These limits are set to keep the

stator below 130

⁰

C while in a stall condition at 25

⁰

C Deg ambient.

Additional over temperature protection is provided by a sensor in the

drive electronics which generates a fault when the board reaches 100

⁰

The factory default setting for action when reaching overtemperature

and continuous overcurrent limits is to immediately disable the drive,

providing drive, motor/actuator or customer tooling protection. The user

may override this protection to allow the actuator to move to a safe

position before disabling or take similar immediate controlled action.

(See the Expert Software Manual, Fault Enables section)

Actuator view

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды