Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя страница 25

Страница: 25 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

Specifications: Size 115 Linear Actuators

T2M

115

Stator

1 Stack

2 Stack

3 Stack

Lead

RPM @ 240 VAC

3000

2000

1500

0.1

Continuous Force

lbf (N)

2,060 (9,163)

3,224 (14,341)

Peak Force

lbf (N)

4,120 (18,327)

5,400 (24,020)

Max Speed

in/sec (mm/sec)

5.00 (127)

3.33 (84)

T2X - C

(Dynamic Load Rating)

lbf (N)

7900 (35141)

T2M - C

(Dynamic Load Rating)

lbf (N)

4736 (21067)

0.2

Continuous Force

lbf (N)

1,177 (5,235)

1,843 (8,198)

2,380 (10,586)

Peak Force

lbf (N)

2,354 (10,471)

3,685 (16,392)

4,760 (21,174)

Max Speed

in/sec (mm/sec)

10.00 (254)

6.67 (169)

5.00 (127)

T2X - C

(Dynamic Load Rating)

lbf (N)

8300 (36920)

T2M - C

(Dynamic Load Rating)

lbf (N)

4890 (21751)

0.5

Continuous Force

lbf (N)

530 (2,358)

829 (3,688)

1,071 (4,764)

Peak Force

lbf (N)

1,059 (4711)

1,658 (7,375)

2,142 (9,528)

Max Speed

in/sec (mm/sec)

25.00 (635)

16.67 (423)

12.50 (317)

T2X - C

(Dynamic Load Rating)

lbf (N)

7030 (31271)

T2M - C

(Dynamic Load Rating)

lbf (N)

4218 (18763)

0.75

Continuous Force

lbf (N)

353 (1,570)

553 (2,460)

714 (3,176)

Peak Force

lbf (N)

706 (3,140)

1,106 (4,920)

1,428 (6,352)

Max Speed

in/sec (mm/sec)

37.5 (953)

25 (635)

17.75 (450)

T2X - C

(Dynamic Load Rating)

lbf (N)

6335 (28179)

T2M - C

(Dynamic Load Rating)

lbf (N)

3328 (14804)

Drive Current @ Continuous Force

Amps

8.5

Available Stroke Lengths

in (mm)

4 (102), 6 (150), 10 (254), 12 (300), 18 (450)

Inertia (zero stroke)

lb-in-s

/ Kg-m

0.01132

(0.000012790)

0.01232

(0.00001392)

0.01332

(0.00001505)

Inertia Adder (per inch of stroke)

lb-in-s

/in/ Kg-m

/in

0.0005640 (0.0000006372)

Approximate Weight

lb (kg)

34 (15.5) for 6 inch stroke, 1 stack. Add 2 (1) per inch of stroke. Add

8 (4) per motor stack. Add 4 (2) for brake.

Operating Temperature Range

20 to 65˚ C (

40˚C available, consult Exlar)

Continuous AC Input Current

Amps

8.3

Ratings based on 25˚C conditions.

** Continuous input current rating is defined by UL and CSA.

*** T2X peak force for 0.1 inch lead is 5400 lbf (24020 N). T2M peak force for 0.1 inch lead limited to 3966 lbf (17,642 N).

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды