Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя

Страница: 18 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

CSA Certified Product

The Tritex II Linear and Rotary Actuators are marked as

shown after passing a rigorous set of design and testing

criteria developed by CSA International (C22.2 No. 139).

This label indicates that CSA certifies this product to be

safe when installed according to the installation guidelines and used with

the scope of the product specifications.

The conditions of acceptability required by CSA are:

•

Drive input maximum continuous operating ratings:

Input Voltage (all models): 240 VAC

, 1 Ф, 50/60 Hz

Drive Model

Drive Description

Input

Continuous

Current (Arms)

R2M090- or R2G090- 90 mm rotary motor

6.3

R2M115- or R2G115- 115 mm rotary motor

8.3

T2M090- or T2X090- 90 mm linear actuator

6.3

T2M115- or T2X115- 115 mm linear actuator

8.3

•

Maximum Rated Force: Up to 3325 lbf (14kN)

•

Installation Requirements

- Hazardous Location (Class I Division 2 Group A, B, C, D)

installations – ½” rigid conduit with NPT connections and use

UL approved copper only wires, 14 AWG, 300 Vac minimum

rating, and 105º C minimum rating shall be used.

- For other non-hazardous locations:

• Use the above connection method, or

• Cable with connector assemblies, or

• Cables with cable glands are permitted.

For additional information on cable installations or part numbers

contact Exlar Corporation.

•

If a customer requires an addi24 VDC power supply to

provide power then it must be a recognized or listed Class 2

Power Supply.

•

Branch circuit protection must be provided. Reference the

manual’s electrical installation section for fuse and circuit breaker

options. Note: branch circuit protection must be located outside

of the hazardous location environment.

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды