Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя

Страница: 78 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

assigned to one of the outputs or to one of the actuator led indicators.

The battery voltage can be displayed on the Diagnostic page while on-

line with the actuator. When battery voltage gets too low to maintain the

count value the Homed Status will be off on the subsequent power up,

requiring the actuator to be re-homed.

Replacing the battery:

The battery is located under the removable cover on the

top of the actuator. For replacement unplug the 2 pin

connector and unsnap the plastic band holding the battery in place and

install a new assembly. Order Exlar PN 42712. The AC input terminals

are located in close proximity, for safety remove AC power before

replacing battery.

Important:

If the battery is removed with both AC and Logic power

also removed, leave all power

off

and do

not

reconnect the battery for

4 minutes

. Once all power is removed from the battery backed logic it

must be allowed enough time to completely bleed down before

restarting. Once power is re-applied the home position must be

reestablished.

Travel limitations.

The counter has a range of +/- 4096 motor revolutions; therefore, the

actuator must operate within this range and if the actuator is moved

beyond this limit a home position must be reestablished.

Speed limitations:

When power is off and the counter is under battery backup, the

maximum rpm the counter can track is 2100 rpm.

WARNING

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды