Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя страница 40

Страница: 40 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

Manual Drive Operating Instructions

Isolate all sources of energy to prevent safety hazard

due to unexpected motion

System design and operating procedures must ensure

that the drive will have no unintended motion that can create a hazard

to personnel when operating the drive manually. This includes electrical

energy turning the motor as well as energy stored in a vertical load

or spring.

There are two manual drive options available on the Tritex, Hand

Wheel (HW) and Side Drive (SD)

The hand wheel option includes an internal switch that is closed when

the hand-wheel drive is fully disengaged and opens when an attempt is

made to engage the hand wheel drive. This switch is in series with the

actuator overtemperature sensor to form a combined run permissive

signal. When manual drive is engaged, an Actuator Overtemperature

fault occurs. The fault action for this fault will disable the drive.

This function is not safety rated, so is not usually sufficient to ensure

safety. Power to the drive must be isolated before manually operation.

The Side Drive does not include and interlock switch so power must

be removed before use.

Important information to avoid damage to the manual

drive

•

If manually driving with a brake engaged or high force is

necessary, please consult Exlar Application Engineering.

•

If a power tool is used to operate the manual side drive the

speed should be limited to 600 RPM

•

An impact driver should never be used to operate the manual

side drive.

•

Determine end of stroke of actuator or system and do not apply

force past it.

•

Refer to

Table 1

for maximum torque specifications.

WARNING

CAUTION

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды