background image

20

EXPERT 64+, rev.12

EXPERT 64+

4.7.  Relay Assignment

4.7.1.  Principle of Operation

Relay Panels : 

The controller can activate up 

to 64 On/Off relays; these relays are located 
in external relay boxes. Up to two RP-32 relay 
panels can be connected to the controller. Refer 
to the wiring diagram enclosed with this manual 
to connect relay panels to the controller.

Vent Door & Tunnel Curtain Relays : 

Relays 

13-14,  15-16,  29-30  and  31-32  the  relay 
panels have specially been designed to open/
close the vent doors and the tunnel curtain. 
It is strongly recommend using these relays 
for this specific purpose: this prevents acti-
vating both the OPEN and CLOSE relays, by 
inadvertence, at the same time.

Fan & Tunnel Fan Relays :  
• Timer-based relays: 

Fan groups and tunnel 

fan groups can activate relays that operate 
in timer mode. These relays allow activating 
cooling  devices  such  as  mist  units  while  a 
specific fan/tunnel fan group is running. Se-
lect “TMR” on a relay to use this function.

• Open/close relays: 

Relays can be used to 

slightly open an air inlet at the start-up of a 
fan/tunnel  group  and  to  close  it  when  the 
fan/tunnel fan group returns to a stop. The 
inlet opens only once at the start-up of the 
chosen fan/tunnel fan group and closes only 
once when the group is disabled. The inlet’s 
running time corresponds to the timer-based 
relay’s On Time. Select 

“OPN”

 to assign an 

opening relay or 

“CLO”

 to assign a closing 

relay on a fan/tunnel fan group. 

  1 

  ---  TMR  ---  ---  ---  ---  --- 

  9 

10 

11  12 

13  14 

15  16 

  ---  ---  ---  ---  ---  ---  ---  ---

  17 

18 

19  20 

21  22 

23  24 

  OPN  ---  CLO  ---  ---  ---  ---  ---

Fan Group 1 Relay Assignment

Selected output

This relay will run in timer 

mode when fan group 1 

is active

This relay will 

runs when 

fan group 1 is 

active

This relay switches at the

startup of fan group 1. The

inlet opens once, during

the timer-based relays’

On time.

The relay switches when

fan group 1 returns to a stop.

The inlet closes once, during

the timer-based relays’

On time.

Relays 13-16 and 29-32 of the relay 

panels have been designed to open 

and close actuators (vent doors or 

tunnel curtains).

Содержание EXPERT 64 Plus













































































Отзывы: