manualshive.com logo in svg

Cray XC30-LC, Процедуры ремонта, Страница: 61 / 173

Поделиться
Скачать
Cray XC30-LC Скачать руководство пользователя страница 61

Figure 54. Circuit Breakers for Cabinet (left) and Blower (right)

a. Close the rear door of the cabinet.

b. Enter the following command in a terminal window on the SMW:

smw$ 

xtcli power up Hostname

Hostname

 is the cabinet, system, or partition ID; examples include 

c0-0

 (for a cabinet), 

S0

 (for a

system), or 

p0

 (for a partition).

2.13 Chassis Host Replacement

2.13.1 Remove a Chassis Host

Prerequisites

Tools Required:

Small slotted screwdriver

Time Required:

5 minutes

About this task

An 

XC Series-AC Chassis Host Replacement

 video is available which shows how to remove and install this

component.

Procedure

1. Power down all of the cabinets in the row.

a. Enter the following command in a terminal window on the SMW:

smw$ 

xtcli power down Hostname

Hostname

 is the cabinet, system, or partition ID; examples include 

c0-0

 (for a cabinet), 

S0

 (for a

system), or 

p0

 (for a partition).

b. For cabinets, place main circuit breakers CB1 and CB2 in the OFF (down) position.

System Cabinet Procedures

 

 61

Содержание XC30-LC














































































































































































Отзывы:

Нет отзывов