Cray XC30-LC Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 173

Cray XC30-LC Скачать руководство пользователя страница 48

Figure 39. Horizontal Bus Bar Assembly Screws

8 screws with

conical washers

J25

J6

J7

J8

J9

J10

J1

J2

J3

J4

J5

8. Disconnect control cables P1 through P6 from the environmental distribution board. If necessary, slide PDU

out to disconnect power cables.

9. Slide the power supply shelf out of the cabinet frame to make the connectors on the rear of the power supply

rack are accessible.

Cables may need to be fed from the rear as the power supply shelf is pulled out.

10. Disconnect the control cables (6) and power cables (6) from the back of the power supply rack and make sure

all are labeled.

11.

CAUTION:

●

Heavy equipment

●

The power supply rack and the horizontal bus bar assembly weigh 118 lbs (54 kg). The power
supply rack must be removed with the assistance of a qualified personnel. Failure to do so may
result in personal injury or equipment damage.

With the assistance of qualified personnel, use proper lifting techniques to place the power supply rack on a
sturdy work surface.

2.9.2

Install a Power Supply Rack

Prerequisites

Tools Required:

T25 Torx driver

T30 Torx driver

IP25 Torx+ driver (14)

Large slotted screwdriver

Time Required:

20 - 25 minutes

IMPORTANT: Any time fasteners are removed from the main power buss structure, like to replace a back
plane or a rectifier rack, there must be an initial torque and a torque verify performed by a second person
during reassembly.

System Cabinet Procedures

48

«
...
46
47
48
49
50
...
»

Содержание XC30-LC














































































































































































Отзывы:

Нет отзывов