manualshive.com logo in svg

Cray XC30-LC, Процедуры ремонта, Страница: 147 / 173

Поделиться
Скачать
Cray XC30-LC Скачать руководство пользователя страница 147

Time Required:

10 minutes

About this task

WARNING:

●

Equipment Damage

●

Do not touch the gold components on the face of the processor chip. This will damage the chip.

Procedure

1. Remove the blade from the cabinet.

2. Remove the T15 Torx screws that attach the shroud to the blade and remove the shroud.

3. Remove the T10 Torx screws that attach the air diffuser bracket to the blade and remove the bracket.

4. Disconnect the power cable connectors (press the release tab and pull cable straight out) and remove the

power cable assembly.

5. Locate the defective processor and remove the processor air duct covering it.

6. Remove the T15 screws (4) securing the heatsink to the KPDC in the correct disassembly order.

Figure 135. Heatsink Assembly Order Closeup

a. Remove the screw labeled 4 completely.

b. Remove the screw labeled 3 completely.

c. Partially remove the screws labeled 1 and 2 working back and forth between them until completely

removed.

Compute and IO Blade Procedures

 

 147

Содержание XC30-LC














































































































































































Отзывы:

Нет отзывов