manualshive.com logo in svg

Cray XC30-LC, Процедуры ремонта, Страница: 163 / 173

Поделиться
Скачать
Cray XC30-LC Скачать руководство пользователя страница 163

9. Replace the shroud and reinstall the T15 Torx attachment screws. Torque to 9 in-lbs.

10. Reinstall the blade into the cabinet.

5.13 GPDC Replacement

5.13.1 Remove a GPDC

Prerequisites

Tools Required:

Adjustable torque driver, 5–40 in-lbs

T15 Torx bit

T10 Torx bit

Dusting gas

Time Required:

15 minutes to remove and replace a populated GPDC

30 minutes to remove a GPDC, transfer the DIMMs and processors to an unpopulated
spare GPDC, and install the GPDC

About this task

If installing a spare GPDC, transfer the DIMMs and processors from the defective GPDC to the new GPDC.

Procedure

1. Remove the blade from the cabinet.

2. Remove the T15 Torx screws that attach the shroud to the blade and remove the shroud.

3. Remove the T10 Torx screws that attach the air diffuser bracket to the blade and remove the bracket.

4. Disconnect the power cable connectors (press the release tab and pull cable straight out) and remove the

power cable assembly.

5. Locate the defective GPDC and remove the processor air ducts covering it.

6. Remove the standoffs (8) that attach the GPDC to the blade with the adjustable torque driver.

The bit holder on the torque driver is the same size as the standoff.

7. Grasp the edges of the GPDC and carefully wiggle the circuit board while pulling straight up to remove it from

the blade.

8.

CAUTION:

Compute and IO Blade Procedures

 

 163

Содержание XC30-LC














































































































































































Отзывы:

Нет отзывов