Conair TrueBlend SB-4 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 168

background image

S e t u p S c r e e n s

( c o n t i n u e d )

S e l f l o a d i n g S e t u p

The blender has the capability to provide self-loading. IT will monitor requests for loads
from the receiver bodies and then sequence the receiver valves and the blower pump to load
material. This feature requires an unlock code. Once unlocked the setup page will provide
two additional setup buttons on the device bar for setting up both the loaders and the blower
pump.

Blower

Control parameters to control the pump/blower device for the self-loading feature.

The basic blower settings are:

NOTE:

With the self-loading system it is possible to provide loading feature for loaders that are

located on a second blender. The (2) blenders must be connected via an Ethernet connec-
tion. The configuration of the loaders includes a remote setting for specifying where the
blower resides. A full explanation of how this system is configured will be explained.

✐

Parameter

Default

Range

Security

Description

Name

Blower x [14 character string] Setup/Stop

The name of the blower pump.

Blower Address

NodeID

[1:255]

Setup/Stop

The Node ID of the touch-panel where the pump
resides. The Node ID is configured via <Setup> -
<IP Address> screen.

Idle Mode

No

Yes/No

Setup/Stop

Select Yes to enable software control of the idle
mode for the pump.

Idle Time (sec)

600

[0:600]

Setup/Stop

The amount of time the pump will run in idle mode
before stopping.

Secondary Pump
Enable

No

Yes/No

Setup/Stop

Once enabled, the secondary pump will be available
as a backup pump.

Selected Pump

Primary

Primary/Secondary

Setup/Stop

Select which pump the primary or secondary pump
will be used for loading the receiver bodies. For the
secondary pump, it must first be enabled.

Secondary Pump
Starter Slot

13

[1:15]

Setup/Stop

The PLC Slot where the secondary pump starter is
connected.

Secondary Pump
Starter Channel

1

[1:12]

Setup/Stop

The PLC IO channel for secondary pump starter.

Primary Pump
Starter Slot

8

[1:15]

Setup/Stop

Select The PLC Slot where the primary pump
starter is connected.

Primary Pump
Starter Channel

9

[1:12]

Setup/Stop

The PLC IO channel for the primary pump starter.

4 - 8 4

l O p e r a t i o n

(Continued)

«
...
120
121
122
123
124
...
»

Содержание TrueBlend SB-4









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TrueBlend SB-4

PRO MEGAMIX HPB300

Бренд: Waring Страницы: 8

Бренд: Waring Страницы: 7

Бренд: Sage Страницы: 84

Бренд: Sage Страницы: 16

ACTIFIT BLSTAFB

Бренд: Oster Страницы: 12

BLSTPEG-G80-000

Бренд: Oster Страницы: 6

Smart Screen Blender DUO

Бренд: Ninja Страницы: 15

Creations Turbo

Бренд: Vitamix Страницы: 28

Бренд: TP-Link Страницы: 8

Бренд: IAGREEA Страницы: 8

Бренд: LINK-MI Страницы: 4

PowerMid Classic PM10C

Бренд: Ebode Страницы: 28

Бренд: Altech Страницы: 31

Бренд: Kuvings Страницы: 10

Бренд: SMART-AVI Страницы: 2

Бренд: TP-Link Страницы: 2

TL-WPA4220 TKIT

Бренд: TP-Link Страницы: 46

FortiExtender 100B

Бренд: Fortinet Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды