Compaq 234664-002 - ProLiant - ML330T02 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 160

background image

6-2

Compaq ProLiant ML330 Generation 2 Server Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer:

Jennifer Hayward

Project:

Compaq ProLiant ML330 Generation 2 Server Setup and Installation Guide

Comments:

Part Number:

234833-001

File Name:

g-ch6 Integrated ATA RAID Utility.doc

Last Saved On:

6/28/01 1:22 PM

RAID Terminology

IMPORTANT:

Only RAID levels 0, 1, and 0+1 are supported by the Integrated ATA RAID

Configuration Utility.

RAID 0 (Stripe)

RAID 0 is a RAID level that involves breaking up data into smaller blocks and
then writing a block to each drive in the array (striping). RAID 0 does not
provide any data redundancy, but does offer the best performance of any
RAID level.

RAID 1 (Mirror)

RAID 1 is a RAID level that involves duplicating all data from one drive to a
second drive (mirroring). RAID 1 provides complete data redundancy, but at
the cost of doubling the required data storage capacity. You must have a
minimum of two hard drives to support RAID 1.

RAID 0+1

RAID 0+1 (also known as RAID 10) is a RAID level that provides both
striping and mirroring capabilities. RAID 0+1 mirrors data from one drive to
another and then stripes the data across a second set of drives. You must have
a minimum of four hard drives to support RAID 0+1.

RAID 5

RAID 5 is not supported by the Integrated ATA RAID Configuration Utility.
It is a RAID level that stripes data and parity information across drives and
requires a minimum of three hard drives.

Spare

The spare option in the utility assigns an extra, unused drive as a spare to be
used in case of a drive failure.

IMPORTANT:

The spare option is applicable only in arrays with redundancy, such as

RAID 1, RAID 0+1, and RAID 5. If a spare is not available, the failed drive must be
replaced with a new drive so that the data on the failed drive can be rebuilt. The
replacement drive capacity must be greater than or equal to the failed drive it replaces.

«
...
98
99
100
101
102
...
»

Содержание 234664-002 - ProLiant - ML330T02

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 234664-002 - ProLiant - ML330T02

Pixie-4 Express

Бренд: XIA Страницы: 17

Бренд: Teagle Страницы: 40

Бренд: Intel Страницы: 108

Бренд: ZALMAN Страницы: 4

Бренд: OpenVox Страницы: 13

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: Uniflair Страницы: 24

Бренд: National Instruments Страницы: 56

Бренд: Digi Страницы: 75

Ultra WiFi Booster

Бренд: Optus Страницы: 8

Бренд: HMS Страницы: 18

Бренд: B&B Electronics Страницы: 24

PSJ-VZ58 gen3 OEM

Бренд: Grizzly Страницы: 12

Бренд: Lucent Technologies Страницы: 7

Blend PRO BP-2002

Бренд: FOLSOM Страницы: 89

ST7-EMU3 Series

Бренд: ST Страницы: 39

Бренд: Advantech Страницы: 59

Бренд: Aaeon Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды