50
1.
Insert the battery in the sensor to be learned and wait until
the led stops flashing.
2.
From the keypad, enter a valid installer code (default master
code 001961).
3.
Press Prog.
4.
The first and second lines of the display will show the
messages “Main Menu” and “Parameter Prog.” respectively,
indicating that you can now modify the system options
5.
Press the Confirm key to enter the respective submenus.
6.
Using the navigation keys (up and down), select “Radio
Zones” submenu. Press confirm.
7.
The display will show the message “Radio Zone 1” and below
it, the parameter that you can modify, namely “Description”.
8.
Using the navigation keys (left and right), select the position
in which you intend to acquire the sensor.
9.
Using the navigation keys (up and down), select “Acquisition”
and press Confirm The display will show the message “Acq.
Radio Zone: In progress...”
10.
Now press and release the tamper button on the sensor.
11.
If acquisition is successful, the display will show the type of
sensor and the unique code number of the sensor.
12.
If acquisition fails because the sensor is already saved
on the control panel, the display will show the message
“Acq. failed Dev. Duplicated” In this case, it is preferable to
acquire the parameters from a PC using the configuration
software, in order to check the programmed sensors, the
acquired codes and their parameters. This will make it
easier to correct any configuration errors.
13.
Once you have finished making changes from the keypad,
remember to transfer them to the PC by means of the
Comelit alarm control panels configuration programme.
1.
Press buttons n° 2 and 3 simultaneously until the radio
control LEDs start flashing autonomously, then release
the buttons and wait for the LEDs to go off. Should this not
happen within about ten seconds (e.g. with a new radio
control) move onto the next point.
2.
From the keypad, enter a valid installer code (default master
code 001961).
3.
Press Prog.
4.
The first and second lines of the display will show the
messages “Main Menu” and “Parameter Prog.” respectively,
indicating that you can now modify the system options
5.
Press the Confirm key to enter the respective submenus.
6.
Using the navigation keys (up and down), select the “Radio
Controls” submenu. Press Confirm
7.
The display will show the message “Radio Control 1”
and below it, the parameter that you can modify, namely
“Description”.
8.
Using the navigation keys (left and right) select the position
in which you intend to acquire the radio control.
9.
Using the navigation keys (up and down), select “Acquisition”
and press Confirm The display will show the message “Acq.
Radio Tel.: In progress...”
10.
Press buttons 3 and 4 simultaneously until the radio control
LEDs start flashing, then release the buttons.
11.
If acquisition is successful, the display will show the
message “DEV. PENDANT” and the unique code number
of the radio control.
12.
Using the navigation keys (up and down), select “User” and
press Confirm
13.
Use the navigation keys to choose the user to whom the
radio control is to be associated and press Confirm.
14.
Once you have finished making changes from the keypad,
remember to transfer them to the PC by means of the
Comelit alarm control panels configuration programme.
1.
Disconnect the siren battery, if connected, and disconnect
the audio from its connector. If the audio is already
disconnected, connect it briefly to discharge the capacitors
in the circuit and ensure subsequent clean switch-on.
2.
From the keypad, enter a valid installer code (default master
code 001961).
3.
Press Prog.
4.
The first and second lines of the display will show the
messages “Main Menu” and “Parameter Prog.” respectively,
indicating that you can now modify the system options
5.
Press the Confirm key to enter the respective submenus.
6.
Using the navigation keys (up and down) select the “Radio
Outputs” submenu. Press confirm.
7.
The display will show the message “Output 1” and below
it, the parameter that you can modify, namely“Description”
8.
Using the navigation keys (left and right) select the position
in which you intend to acquire the radio control.
9.
Using the navigation keys (up and down) select “Acquisition”.
10.
Press and hold the siren's LEARN button, which is located
near the connection strip for the configuration jumpers, and
connect the battery. Hold the LEARN button down until the
siren flashing light starts flashing quickly, then release the
button.
11.
Wait until the flasher starts flashing more slowly.
12.
Now press Confirm on the keypad. The display will show the
message “Acq. Radio Tel.: In progress...”
13.
After about fifteen seconds, the result of the acquisition will
appear on the display.
14.
Once you have finished making changes from the keypad,
remember to transfer them to the PC by means of the
Comelit alarm control panels configuration programme.
To exit programming mode, simply press C until you have
exited the menus completely, i.e. until the date and time are
displayed on the keypad.
You can reset the control panel configuration at two levels: level
one, defined as Partial, and level two, defined as Total.
A total reset reconfigures the control panel card to its default
settings, in such a way that it can be re-used as though newly
unpacked from its packaging. Total resets can be performed
only via the configuration software, provided you know both a
user code and an installer code. It may be necessary to perform
a partial reset to recover the necessary codes.
The total reset process is described in the procedures set
down in the system configuration manual.
A partial reset is confined to recovering the control panel codes,
thereby making it possible to restore a system from which all
the necessary codes for use and management have been lost.
A partial reset can be performed in hardware mode only.
To perform a partial reset to recover the default master installer
and user codes, proceed as follows:
1.
Switch off all power to the control panel card
2.
Insert a jumper on connector JP6
3.
Power up the control panel
4.
Wait until LED DL3 starts flashing at about 1 flash per
second
5.
Remove the jumper from JP6
6.
The codes are now restored to their factory settings
5.3.15 Acquiring a radio sensor code from the
keypad
5.3.16 Acquiring a radio control code from the
keypad
5.3.17 Acquiring a siren code from the keypad
5.3.18 Exiting programming mode
5.3.19 Restoring factory settings
TOTAL RESET
PARTIAL RESET (CODE RECOVERY)
