49
1.
Press the prog key on the keypad: the display will show the
message 1 Config. Bus followed by two vertical arrows (up
and down).
2.
Press confirm .
3.
Enter the serial number of the first keypad by typing the
digits 001 in sequence, and then press confirm.
4.
The display now shows the message SERIAL COM. Speed:
with the proposal "38400".
5.
Press confirm.
1.
From the keypad, enter a valid user code (default 111111)
followed by either the Partial 1 key or the Partial 2 key.
2.
If necessary, use the up and down navigation keys to select a different
scenario from the proposed scenario, and then press Confirm.
3.
The keypad confirms the action with the message:
“ACTIVATED”
1.
From the keypad, enter a valid user code (the default setting
is 111111) and then press the ON key
2.
The keypad asks for confirmation: “TOTAL ACTIVATION?”
3.
Press the Confirm key to confirm.
4.
The keypad confirms the action with the message:
“ACTIVATED”
√
To change the date and time from the keypad, you
need to go into programming mode.
1.
From the keypad, enter a valid installer code (default master
code 001961).
2.
Press Prog.
3.
The first and second lines of the display will show the
messages “Main Menu” and “Parameter Prog.” respectively,
indicating that you can now modify the system options
4.
Press the Confirm key to enter the respective submenus.
5.
Using the navigation keys (up and down) select
“ProximityKeys” submenu. Press confirm.
6.
The display will show the message “Key 1” and below it, the
parameter that you can modify, namely “Description”
7.
Using the navigation keys (left and right), select the number
of the key you intend to acquire.
8.
Press Confirm if you intend to change the description,
then confirm to make the change or press C to leave the
description as it is.
9.
Using the navigation keys (up and down), select the
"Acquire" submenu. Still using the navigation keys, select
the type of peripheral from which you intend to acquire the
key code and its bus address, then press Confirm again.
10.
The display will show the message “Acq. Key: In progress...”
11.
Bring the key close to the RFID reader: the message will
change from "In progress..." to "Acquired".
12.
Press Confirm: the display will show a description of the
colour of the key's plastic housing
13.
Press Confirm again to associate the key to the desired
user.
14.
Once you have finished making changes from the keypad,
remember to transfer them to the PC by means of the
Comelit alarm control panels configuration programme.
As installer:
As user:
1.
Go into programming mode as an installer (see relevant
paragraph).
2.
Using the navigation keys, select “System Mgmt.”, then
continue as a user.
1.
Go into programming mode as a user (see relevant
paragraph).
2.
Using the navigation keys (up and down), select the
“Options” menu on the second line of the display, and press
Confirm.
3.
Using the navigation keys (up and down), select the “Change
date/time” option on the second line, and press Confirm.
4.
The first line will show DD-MM-YY (day, month and year)
and the second line will display the date set on the control
panel.
5.
Enter the date using the number keys (e.g.: 1 September
2012 becomes 010912), then confirm.
6.
The first line of the display now shows HH-MM (hours and
minutes) and the second line shows the time set on the
control panel.
7.
Enter the time in the format displayed (e.g. 1.15 pm becomes
1315), then confirm.
8.
This done, the display will show the message PARAMETER
CHANGED.
9.
Press C to go up one level in the menu, or C repeatedly until
the date and time appear on the keypad.
1.
From the keypad, enter a valid user code (the default setting
is 111111) and then press the OFF key.
2.
The keypad confirms the action with the message:
“DEACTIVATED”
3.
Deactivation will also deactivate any alarms in progress
within a few seconds.
1.
From the keypad, enter a valid user code (default 111111)
2.
Press Prog.
3.
The first line of the display will show the message "System
Mgmt.” indicating that you can now modify the system
options.
1.
Go into programming mode as a user (see previous
paragraph).
2.
Using the navigation keys (up and down), select the
“COMMANDS” menu on the second line of the display, and
press Confirm: the message “GENERATE COMMAND” will
appear on the first line of the display.
3.
Using the navigation keys (up and down), select “AUTH.
INSTALLER?” on the second line, and press Confirm: the
message “DONE” will appear on the display.
4.
Press C until you have exited the menus completely (i.e.
until the date and time are displayed on the keypad).
5.
From the keypad, enter a valid installer code (default master
code 001961).
6.
Press Prog.
7.
The first and second lines of the display will show the
messages “Main Menu” and “Parameter Mgmt.” indicating
√
The installer code must be authorised by the user, so
the procedure is as follows:
1.
From the keypad, enter a valid user code (default 111111).
2.
Once the code has been recognised, press the Prog key
until the message “DONE” appears on the screen.
3.
This will mute the alarm.
» Keypad number one will now be taken in charge by the
control panel and can be used for activating, deactivating
and configuring the system.
5.3.7 Total activation of the alarm system
5.3.13 Changing date and time
5.3.14 Acquiring an RFID key code from the keypad
5.3.8 Partial activation of the alarm system /
execution of a scenario
5.3.9 Total deactivation of the alarm system
5.3.11 Entering programming as a User
5.3.12 Entering programming as an Installer
(installer code authorisation)
5.3.10 Muting an alarm with the system deactivated
that you can now display or modify the system options.
8.
From this position, you can use the navigation keys to
select either the “System Mgmt.” menu, which corresponds
to the user menu, or the “Parameter Prog.” menu, which is
reserved for the installer.
9.
Press the Confirm key to enter the respective submenus.
5.3.6 Setting the keypad serial number
At first start-up, the keypad displays the message NOT
CONNECTED. To enable the control panel to recognise
keypad number 1 (the only keypad that can be recognised by
the control panel by default), proceed as follows:
