Cole Parmer Jenway 7410 Скачать руководство пользователя страница 61

Страница: 61 / 68

Section 16 - Troubleshooting

During initial power on self-test (POST)

The following errors can appear during the initial self-test.

A hardware problem has been detected. You may continue to use the instrument but calibration data may have

been affected causing any readings to be inaccurate. Contact Cole-Parmer support and quote error code 101.

A hardware problem has been detected. Contact Cole-Parmer support and quote error code 102.

A potential hardware problem has been detected. If the lid is currently open, close it and try again. If it’s

currently closed, contact Cole-Parmer support and quote error code 103.

A hardware problem has been detected. Contact Cole-Parmer support and quote error code 104.

A hardware problem has been detected. Contact Cole-Parmer support and quote error code 105.

A hardware problem has been detected. Contact Cole-Parmer support and quote error code 106.

A hardware problem has been detected. Contact Cole-Parmer support and quote error code 107.

A potential hardware problem has been detected. If there’s currently a sample in the instrument, remove it

and try again. If there’s no sample in the instrument, contact Cole-Parmer support and quote error code 108.

A potential hardware problem has been detected. If there’s currently a sample in the instrument, remove it

and try again. If there’s no sample in the instrument, contact Cole-Parmer support and quote error code 109.

A potential hardware problem has been detected with the fitted microvolume accessory. Contact Cole-Parmer

support and quote error code 110.

A potential hardware problem has been detected with the fitted cell changer accessory. Contact Cole-Parmer

support and quote error code 111.

Содержание Jenway 7410





































































Результаты поиска

Содержание Jenway 7410

Отзывы:

Похожие инструкции для Jenway 7410

Бренды по названию

Популярные бренды

Cole Parmer Jenway 7410, Инструкция по эксплуатации

Результаты поиска

Содержание Jenway 7410

Отзывы:

Похожие инструкции для Jenway 7410

Бренды по названию

Популярные бренды