Cole Parmer Jenway 7410 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 68

background image

10.2

Calibration

The calibration must be performed at the same wavelengths at which the sample will be measured. Insert a cuvette

containing the blank solution into the sample chamber and close the instrument lid. Touch the

icon. This sets

the instrument to zero absorbance and 100% transmittance.

10.3

Sample Measurement

It is not possible to measure a sample before the instrument has been calibrated at the selected wavelengths.Once

the calibration has been performed the

icon becomes active and a sample can be measured. Remove the

cuvette containing the blank solution and place a cuvette containing the sample to be measured in the sample

holder. Close the instrument lid and touch the

icon. Once the measurement is completed the result will

be shown on the screen. Touch

to measure subsequent samples can be measured in the same way. If

any of the wavelengths are adjusted between sample measurements then the instrument must be calibrated again

before more samples can be measured.

44

«
...
42
43
44
45
46
...
»

Содержание Jenway 7410





































































Отзывы:

Нет отзывов

Похожие инструкции для Jenway 7410

Бренд: ICT Страницы: 48

Бренд: OfiTE Страницы: 67

Бренд: Bacharach Страницы: 28

Бренд: OHAUS Страницы: 52

Бренд: Omano Страницы: 14

Бренд: Topcon Страницы: 62

Бренд: Magnescale Страницы: 64

SourceMeter 2430

Бренд: Keithley Страницы: 141

Бренд: Conrad Electronic Страницы: 38

Бренд: LEM Страницы: 33

Dakota Ultrasonics ZX-2

Бренд: ABQ Industrial Страницы: 27

Бренд: Primes Страницы: 56

Бренд: Lutron Electronics Страницы: 43

Бренд: E+E Elektronik Страницы: 20

Бренд: Brooks Страницы: 64

Бренд: brena Страницы: 26

Бренд: Lutron Electronics Страницы: 23

Бренд: Aalborg Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды