Cole Parmer Jenway 7410 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 68

background image

39

If a lag time has been set the instrument will count down the lag time before the kinetics run starts. If no lag time
has been set the kinetics run starts straight away and a live kinetics run is shown on the screen.

If the kinetics run needs to be stopped touch

. A warning message will appear asking for confirmation

to stop the kinetics run. Touch

to stop the run, touch

to carry on with the kinetic run.

Once the measurement time is complete the full kinetics run will be shown on the screen. To run the kinetics
experiment again using the same method parameters touch

. Subsequent samples can be measured

in the same way. If the wavelength is adjusted between sample measurements then the instrument must be
calibrated again before more samples can be measured.

«
...
37
38
39
40
41
...
»

Содержание Jenway 7410





































































Отзывы:

Нет отзывов

Похожие инструкции для Jenway 7410

Бренд: Landis+Gyr Страницы: 54

Бренд: Kawai Страницы: 2

Бренд: ABQ Industrial Страницы: 15

Бренд: ABQINDUSTRIAL Страницы: 3

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

Бренд: jenway Страницы: 50

Бренд: jenway Страницы: 62

Бренд: M-system Страницы: 13

Бренд: Maico Страницы: 27

Бренд: Magnescale Страницы: 14

Бренд: National Instruments Страницы: 38

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: PCE Health and Fitness Страницы: 11

Бренд: Kawai Страницы: 110

Бренд: Dakota Digital Страницы: 34

Бренд: Value Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды