Cole Parmer Jenway 7410 Скачать руководство пользователя страница 35

Страница: 35 / 68

Specific points can be selected on the graph by touching the graph, a sliding cursor will appear. It is possible to

move the cursor by dragging left or right.

The curve fit algorithm can be changed by touching

. Select between linear through zero,

linear, quadratic through zero and quadratic.

The curve statistics are also displayed for the curve fit chosen. For example if the curve fit is y = mx+c the curve
statistics displayed will be the gradient of the line (m), constant (c) and correlation coefficient (r²).

Once all the standards have been measured touch

and then the unknown samples can be measured.

8.4

Sample Measurement

Place a cuvette containing the sample to be measured in the sample holder. Close the instrument lid and touch the

. Once the measurement is completed the concentration and photometric results will be shown on the screen

. Subsequent samples can be measured in the same way. If the wavelength is adjusted between sample

measurements then the instrument must be calibrated again and a new standard curve must be created before

more samples can be measured.

To change the curve fit at any time touch

to return to the standard curve screen.

Содержание Jenway 7410





































































Результаты поиска

Содержание Jenway 7410

Отзывы:

Похожие инструкции для Jenway 7410

Бренды по названию

Популярные бренды

Cole Parmer Jenway 7410, Инструкция по эксплуатации

Результаты поиска

Содержание Jenway 7410

Отзывы:

Похожие инструкции для Jenway 7410

Бренды по названию

Популярные бренды