Cole Parmer Jenway 7410 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 68

background image

26

Section 7 - Spectrum

The spectrum measurement mode enables measurements of absorbance or % transmittance over a range of
wavelengths to be performed. The absorbance or % transmittance at each wavelength is plotted graphically. Post
measurement tools such as peaks and valleys analysis and area under the graph can be performed. This operating
mode can be used to partially characterise a sample. Touch the Spectrum icon on the main menu to enter this
measurement mode.

7.1

Method Set up

The parameters which can be entered in this measurement mode are start and end wavelength, scan interval and
measurement mode. Once all the required parameters have been entered a calibration can be performed.

7.1.1

Setting Start and End Wavelengths

Model 7410 can perform measurements from 320nm to 1000nm; model 7415 can perform measurements from

198 to 1000nm. To adjust the start wavelength, touch

and use the keypad to enter the required

wavelength. Touch

to apply the entered wavelength and return to the method set up. The end wavelength

can be adjusted in the same way.

The start and end wavelengths must be different. If the same value is entered an error message will be displayed.

«
...
24
25
26
27
28
...
»

Содержание Jenway 7410





































































Отзывы:

Нет отзывов

Похожие инструкции для Jenway 7410

Бренд: ECC X-RAY Страницы: 14

Бренд: jablotron Страницы: 2

Бренд: National Instruments Страницы: 15

Бренд: E Instruments Страницы: 144

Бренд: Dewetron Страницы: 24

Бренд: NCS Страницы: 7

Бренд: Ferret Страницы: 18

Бренд: Bartec Страницы: 38

Бренд: SEAWARD Electronic Страницы: 57

Бренд: Omega Страницы: 13

Бренд: Carman Страницы: 64

Multimar 25 EWR

Бренд: Mahr Страницы: 20

Бренд: Hantek Страницы: 40

Бренд: Opsytec Страницы: 37

Бренд: Hanna Instruments Страницы: 12

Бренд: KAM Страницы: 4

Бренд: Easy-Laser Страницы: 86

Бренд: Jacob Jensen Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды