Cisco WLC 5700 Series Скачать руководство пользователя | Manualshive

Страница: 23 / 82

background image

Do not enable Layer 3 addresses on the physical EtherChannel ports. Do not assign bridge groups on the
physical EtherChannel ports because it creates loops.

Caution

Examples

This example shows how to configure an EtherChannel on a single controller in the stack. It assigns two
static-access ports in VLAN 10 to channel 5 with the PAgP mode desirable:

Controller#

configure terminal

Controller(config)#

interface range gigabitethernet2/0/1 -2

Controller(config-if-range)#

switchport mode access

Controller(config-if-range)#

switchport access vlan 10

Controller(config-if-range)#

channel-group 5 mode desirable

Controller(config-if-range)#

end

This example shows how to configure an EtherChannel on a single controller in the stack. It assigns two
static-access ports in VLAN 10 to channel 5 with the LACP mode active:

Controller#

configure terminal

Controller(config)#

interface range gigabitethernet2/0/1 -2

Controller(config-if-range)#

switchport mode access

Controller(config-if-range)#

switchport access vlan 10

Controller(config-if-range)#

channel-group 5 mode active

Controller(config-if-range)#

end

This example shows how to configure a cross-stack EtherChannel in a controller stack. It uses LACP passive
mode and assigns two ports on stack member 2 and one port on stack member 3 as static-access ports in VLAN
10 to channel 5:

Controller#

configure terminal

Controller(config)#

interface range gigabitethernet2/0/4 -5

Controller(config-if-range)#

switchport mode access

Controller(config-if-range)#

switchport access vlan 10

Controller(config-if-range)#

channel-group 5 mode passive

Controller(config-if-range)#

exit

Controller(config)#

interface gigabitethernet3/0/3

Controller(config-if)#

switchport mode access

Controller(config-if)#

switchport access vlan 10

Controller(config-if)#

channel-group 5 mode passive

Controller(config-if)#

exit

You can verify your settings by entering the

show running-config

privileged EXEC command.

Related Commands

Description

Command

Restricts the protocol used on a port to manage channeling.

channel-protocol

Accesses or creates a port channel.

interface port-channel

Displays EtherChannel information for a channel.

show etherchannel

Displays LACP channel-group information.

Displays Port Aggregation Protocol (PAgP) channel-group
information.

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

15

Layer 2/3 Commands

channel-group

«
...
21
22
23
24
25
...
»

Содержание WLC 5700 Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для WLC 5700 Series

DES-3526 - Switch - Stackable

Бренд: D-Link Страницы: 258

Бренд: Abocom Страницы: 11

Бренд: Abocom Страницы: 19

Ethernet Communication Module DVPEN01-SL

Бренд: Delta Electronics Страницы: 54

Бренд: Campbell Страницы: 38

NVIP- NVRA0104/GO

Бренд: Novus Страницы: 44

Бренд: Eaton Страницы: 14

Бренд: F.F. Group Страницы: 56

Бренд: Teldat Страницы: 47

32R1860 - Nortel Layer 2/3 Copper GbE Switch...

Бренд: IBM Страницы: 14

Бренд: Planet Страницы: 16

Бренд: Westermo Страницы: 13

Бренд: Crestron Страницы: 2

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 19

Бренд: ABB Страницы: 62

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды