Cisco WLC 5700 Series Скачать руководство пользователя | Manualshive

Страница: 71 / 82

background image

switchport mode

To configure the VLAN membership mode of a port, use the

switchport mode

command in interface

configuration mode. To reset the mode to the appropriate default for the device, use the

no

form of this

command.

switchport mode

{

access| dynamic

| {

auto| desirable

}

| trunk

}

noswitchport mode

{

access| dynamic

| {

auto| desirable

}

| trunk

}

Syntax Description

Sets the port to access mode (either static-access or dynamic-access depending on the
setting of the

switchport access vlan

interface configuration command). The port is

set to access unconditionally and operates as a nontrunking, single VLAN interface that
sends and receives nonencapsulated (non-tagged) frames. An access port can be assigned
to only one VLAN.

access

Sets the port trunking mode dynamic parameter to auto to specify that the interface
convert the link to a trunk link. This is the default switchport mode.

dynamic auto

Sets the port trunking mode dynamic parameter to desirable to specify that the interface
actively attempt to convert the link to a trunk link.

dynamic desirable

Sets the port to trunk unconditionally. The port is a trunking VLAN Layer 2 interface.
The port sends and receives encapsulated (tagged) frames that identify the VLAN of
origination. A trunk is a point-to-point link between two controllers or between a
controller and a router.

trunk

Command Default

The default mode is

dynamic auto

.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

Although visible in the CLI, the

dot1q-tunnel

keyword is not supported.

Note

A configuration that uses the

access

,or

trunk

keywords takes effect only when you configure the port in the

appropriate mode by using the

switchport mode

command. The static-access and trunk configuration are

saved, but only one configuration is active at a time.

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

63

Layer 2/3 Commands

switchport mode

«
...
69
70
71
72
73
...
»

Содержание WLC 5700 Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для WLC 5700 Series

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 83

Бренд: D-Link Страницы: 129

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 21

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 86

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 4

DSL-3580L Series

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 64

Бренд: D-Link Страницы: 73

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

Бренд: Paradyne Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды