Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 74 / 82

switchport nonegotiate

To specify that Dynamic Trunking Protocol (DTP) negotiation packets are not sent on the Layer 2 interface,
use the

switchport nonegotiate

command in interface configuration mode. Use the

form of this command

to return to the default setting.

switchport nonegotiate

no switchport nonegotiate

Syntax Description

This command has no arguments or keywords.

Command Default

The default is to use DTP negotiation to learn the trunking status.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

The

no switchport nonegotiate

command removes nonegotiate status.

This command is valid only when the interface switchport mode is access or trunk (configured by using the

switchport mode access

or the

switchport mode trunk

interface configuration command). This command

returns an error if you attempt to execute it in dynamic (auto or desirable) mode.

Internetworking devices that do not support DTP might forward DTP frames improperly and cause
misconfigurations. To avoid this problem, turn off DTP by using the

switchport nonegotiate

command to

configure the interfaces connected to devices that do not support DTP to not forward DTP frames.

When you enter the

switchport nonegotiate

command, DTP negotiation packets are not sent on the interface.

The device does or does not trunk according to the

mode

parameter:

access

trunk.

•

If you do not intend to trunk across those links, use the

switchport mode access

interface configuration

command to disable trunking.

•

To enable trunking on a device that does not support DTP, use the

switchport mode trunk

and

switchport

nonegotiate

interface configuration commands to cause the interface to become a trunk but to not

generate DTP frames.

Examples

This example shows how to cause a port to refrain from negotiating trunking mode and to act as a trunk or
access port (depending on the mode set):

Controller(config)#

interface gigabitethernet2/0/1

Controller(config-if)#

switchport nonegotiate

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Layer 2/3 Commands

switchport nonegotiate

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды