Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 79 / 82

•

The

shutdown

and

no shutdown

interface configuration commands.

•

The

no udld enable

global configuration command, followed by the

udld {aggressive | enable}

global

configuration command reenables UDLD globally.

•

The

no udld port

interface configuration command, followed by the

udld port

udld port aggressive

interface configuration command reenables UDLD on the specified interface.

•

The

errdisable recovery cause udld

and

errdisable recovery interval interval

global configuration

commands automatically recover from the UDLD error-disabled state.

Examples

This example shows how to enable UDLD on an port:

Controller(config)#

interface gigabitethernet6/0/1

Controller(config-if)#

udld port

This example shows how to disable UDLD on a fiber-optic interface despite the setting of the

udld

global

configuration command:

Controller(config)#

interface gigabitethernet6/0/1

Controller(config-if)#

no udld port

You can verify your settings by entering the

show running-config

or the

show udld interface

privileged

EXEC command.

Related Commands

Description

Command

Displays UDLD administrative and operational status for all ports or the specified
port.

show udld

Enables aggressive or normal mode in UDLD or sets the configurable message
timer time.

udld

Resets all interfaces shut down by UDLD and permits traffic to pass through
again.

udld reset

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Layer 2/3 Commands

udld port

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды