Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 77 / 82

•

The

shutdown

and

no shutdown

interface configuration commands.

•

The

no udld enable

global configuration command followed by the

udld {aggressive | enable}

global

configuration command to reenable UDLD globally.

•

The

no udld port

interface configuration command followed by the

udld port

udld port aggressive

interface configuration command to reenable UDLD on the specified interface.

•

The

errdisable recovery cause udld

and

errdisable recovery interval interval

global configuration

commands to automatically recover from the UDLD error-disabled state.

Examples

This example shows how to enable UDLD on all fiber-optic interfaces:

Controller(config)#

udld enable

You can verify your setting by entering the

show udld

privileged EXEC command.

Related Commands

Description

Command

Displays UDLD administrative and operational status for all ports or the specified
port.

show udld

Enables UDLD on an individual interface or prevents a fiber-optic interface from
being enabled by the

udld

global configuration command.

udld port

Resets all interfaces shut down by UDLD and permits traffic to pass through
again.

udld reset

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Layer 2/3 Commands

udld

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды