Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 10 / 82

Table 1: Command Mode Summary

About This Mode

Exit Method

Prompt

Access Method

Mode

Use this mode to

•

Change
terminal
settings.

•

Perform basic
tests.

•

Display
system
information.

Enter

logout

quit

Switch>

Begin a session with
your switch.

User EXEC

Use this mode to
verify commands
that you have
entered. Use a
password to protect
access to this mode.

Enter

disable

exit.

Controller#

While in user EXEC
mode, enter the

enable

command.

Privileged EXEC

Use this mode to
configure
parameters that
apply to the entire
switch.

To exit to privileged
EXEC mode, enter

exit

end

, or press

Ctrl-Z

Controller(config)#

While in privileged
EXEC mode, enter
the

configure

command.

Global
configuration

Use this mode to
configure VLAN
parameters. When
VTP mode is
transparent, you can
create
extended-range
VLANs (VLAN IDs
greater than 1005)
and save
configurations in the
switch startup
configuration file.

To exit to global
configuration mode,
enter the

exit

command.

To return to
privileged EXEC
mode, press

Ctrl-Z

or enter

end

Controller(config-vlan)#

While in global
configuration mode,
enter the

vlan

vlan-id

command.

VLAN
configuration

Use this mode to
configure
parameters for the
Ethernet ports.

To exit to global
configuration mode,
enter

exit

To return to
privileged EXEC
mode, press

Ctrl-Z

or enter

end

Controller(config-if)#

While in global
configuration mode,
enter the

interface

command (with a
specific interface).

Interface
configuration

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Using the Command-Line Interface

Understanding Command Modes

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды