Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 62 / 82

show platform etherchannel

To display platform-dependent EtherChannel information, use the

show platform etherchannel

command

in privileged EXEC mode.

show platform etherchannel channel-group-number

{

group-mask

load-balance mac src-mac dst-mac

[

src-ip dst-ip

[

port src-port dst-port

]]}

Syntax Description

Channel group number. The range is 1 to 128.

channel-group-number

Displays EtherChannel group mask.

group-mask

Tests EtherChannel load-balance hash algorithm.

load-balance

Specifies the source and destination MAC addresses.

mac src-mac dst-mac

(Optional) Specifies the source and destination IP addresses.

ip src-ip dst-ip

(Optional) Specifies the source and destination layer port numbers.

port src-port dst-port

Command Default

None

Command Modes

Privileged EXEC

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

Use this command only when you are working directly with a technical support representative while
troubleshooting a problem.

Do not use this command unless a technical support representative asks you to do so.

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Layer 2/3 Commands

show platform etherchannel

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды