Cisco WLC 5700 Series Скачать руководство пользователя | Manualshive

Страница: 9 / 82

background image

Using the Command-Line Interface

This chapter contains the following topics:

•

Using the Command-Line Interface, page 1

Using the Command-Line Interface

This chapter describes the Cisco IOS command-line interface (CLI) and how to use it to configure your switch.

Understanding Command Modes

The Cisco IOS user interface is divided into many different modes. The commands available to you depend
on which mode you are currently in. Enter a question mark (?) at the system prompt to obtain a list of commands
available for each command mode.

When you start a session on the switch, you begin in user mode, often called user EXEC mode. Only a limited
subset of the commands are available in user EXEC mode. For example, most of the user EXEC commands
are one-time commands, such as

show

commands, which show the current configuration status, and

clear

commands, which clear counters or interfaces. The user EXEC commands are not saved when the switch
reboots.

To have access to all commands, you must enter privileged EXEC mode. Normally, you must enter a password
to enter privileged EXEC mode. From this mode, you can enter any privileged EXEC command or enter
global configuration mode.

Using the configuration modes (global, interface, and line), you can make changes to the running configuration.
If you save the configuration, these commands are stored and used when the switch reboots. To access the
various configuration modes, you must start at global configuration mode. From global configuration mode,
you can enter interface configuration mode and line configuration mode.

This table describes the main command modes, how to access each one, the prompt you see in that mode, and
how to exit the mode. The examples in the table use the hostname

Switch

.

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

1

«
...
7
8
9
10
11
...
»

Содержание WLC 5700 Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для WLC 5700 Series

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 3

Fieldpoint cFP-RTD-124

Бренд: National Instruments Страницы: 15

AyrMesh IndoorAP

Бренд: AYRSTONE Страницы: 2

Бренд: Juniper Страницы: 2

Бренд: Patton electronics Страницы: 2

NetVanta Analog Modem Dial Backup Interface Module

Бренд: ADTRAN Страницы: 2

Бренд: Valcom Страницы: 4

Acme Packet 3900

Бренд: Oracle Страницы: 70

7798 I/SITE LAN

Бренд: CSI Страницы: 56

GigaSpire BLAST u4hm

Бренд: Calix Страницы: 45

Бренд: Tripp Lite Страницы: 3

Бренд: Siklu Страницы: 52

Бренд: 3Com Страницы: 17

Бренд: NASdeluxe Страницы: 6

Бренд: ZPE Страницы: 2

DXS-3600 Series

Бренд: D-Link Страницы: 1456

Бренд: Supero Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды