Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 64 / 82

show udld

To display UniDirectional Link Detection (UDLD) administrative and operational status for all ports or the
specified port, use the

show udld

command in user EXEC mode.

show udld

[

Auto-Template

Capwap

GigabitEthernet

GroupVI

InternalInterface

Loopback

Null

Port-channel

TenGigabitEthernet

Tunnel

Vlan

]

interface_number

show udld neighbors

Syntax Description

(Optional) Displays UDLD operational status of the
auto-template interface. The range is from 1 to 999.

Auto-Template

(Optional) Displays UDLD operational status of the CAPWAP
interface. The range is from 0 to 2147483647.

Capwap

(Optional) Displays UDLD operational status of the
GigabitEthernet interface. The range is from 0 to 9.

GigabitEthernet

(Optional) Displays UDLD operational status of the group virtual
interface. The range is from 1 to 255.

GroupVI

(Optional) Displays UDLD operational status of the internal
interface. The range is from 0 to 9.

InternalInterface

(Optional) Displays UDLD operational status of the loopback
interface. The range is from 0 to 2147483647.

Loopback

(Optional) Displays UDLD operational status of the null
interface.

Null

(Optional) Displays UDLD operational status of the Ethernet
channel interfaces. The range is from 1 to 128.

Port-channel

(Optional) Displays UDLD operational status of the Ten Gigabit
Ethernet interface. The range is from 0 to 9.

TenGigabitEthernet

(Optional) Displays UDLD operational status of the tunnel
interface. The range is from 0 to 2147483647.

Tunnel

(Optional) Displays UDLD operational status of the VLAN
interface. The range is from 1 to 4095.

Vlan

(Optional) ID of the interface and port number. Valid interfaces
include physical ports, VLANs, and port channels.

interface-id

(Optional) Displays neighbor information only.

neighbors

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Layer 2/3 Commands

show udld

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды