Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 55 / 82

show lacp

To display Link Aggregation Control Protocol (LACP) channel-group information, use the

show lacp

command

in user EXEC mode.

show lacp

[

channel-group-number

] {

counters| internal| neighbor| sys-id

}

Syntax Description

(Optional) Channel group number. The range is 1 to 128.

channel-group-number

Displays traffic information.

counters

Displays internal information.

internal

Displays neighbor information.

neighbor

Displays the system identifier that is being used by LACP. The system
identifier consists of the LACP system priority and the controller MAC
address.

sys-id

Command Default

None

Command Modes

User EXEC

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

You can enter any

show lacp

command to display the active channel-group information. To display specific

channel information, enter the

show lacp

command with a channel-group number.

If you do not specify a channel group, information for all channel groups appears.

You can enter the

channel-group-number

to specify a channel group for all keywords except

sys-id

Examples

This is an example of output from the

show lacp counters

user EXEC command. The table that follows

describes the fields in the display.

Controller>

show lacp counters

LACPDUs

Marker

Marker Response

LACPDUs

Port

Sent

Recv

Sent

Recv

Sent

Recv

Pkts

Err

---------------------------------------------------------------------
Channel group:1
Gi2/0/1

Gi2/0/2

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Layer 2/3 Commands

show lacp

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды