Cisco UCS C210 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 124

background image

2-17

Cisco UCS C210 Server Installation and Service Guide

OL-20887-02

Chapter

Clearing the CIMC Admin Password Using Jumper J45

This procedure describes how to clear the CIMC admin password back to the default in case the
user-selected password is lost of forgotten.

Step 1

Power off the server as described in the

“Shutting Down and Powering Off the Server” section on

page 3-8

.

Step 2

Disconnect all power cords from the power supplies.

Step 3

Slide the server out the front of the rack far enough so that you can remove the top cover. You might have
to detach cables from the rear panel to provide clearance.

Caution

If you cannot safely view and access the component, remove the server from the rack.

Step 4

Remove the top cover as described in the

“Removing and Replacing the Server Top Cover” section on

page 3-10

.

Step 5

Move the shorting jumper to pins 2 and 3 of the J45 header (see

Figure 2-6 on page 2-15

).

Step 6

Reinstall the top cover and reconnect AC power cords to the server. The server powers up to standby
power mode, indicated when the Power LED on the front panel is amber.

Step 7

Return the server to main power mode by pressing the

Power

button on the front panel. The server is in

main power mode when the Power LED is green.

Note

You must allow the entire server to reboot to main power mode to complete the password reset.
This is because the state of the J45 jumper cannot be determined without the host CPU running.
The password is then cleared.

Step 8

Press the

Power

button to shut down the server to standby power mode, and then remove AC power cords

from the server to remove all power.

Step 9

Remove the top cover from the server.

Step 10

Remove the shorting jumper from the header pins.

Note

If you do not remove the jumper, the password is cleared every time that you power-cycle the
server.

Step 11

Replace the top cover, replace the server in the rack, replace power cords and any other cables, then
power on the server by pressing the

Power

button.

«
...
33
34
35
36
37
...
»

Содержание UCS C210





























































































































Отзывы:

Нет отзывов

Похожие инструкции для UCS C210

Бренд: 360 Systems Страницы: 117

Бренд: MSI Страницы: 106

DIGI CONNECT ES

Бренд: Digi Страницы: 23

IP-DECT SERVER 6500

Бренд: SpectraLink Страницы: 2

SUPERSERVER 5028TK-HTR

Бренд: Supermicro Страницы: 138

Бренд: JIEYUN TECHNOLOGY Страницы: 25

8-BAY RACKMOUNT NAS

Бренд: Seagate Страницы: 20

BlackArmor NAS 420

Бренд: Seagate Страницы: 64

Бренд: BITMAIN Страницы: 15

Бренд: Viavi Страницы: 8

Smartstor NS4600

Бренд: Promise Technology Страницы: 370

Бренд: Solid Страницы: 102

Бренд: Black Box Страницы: 46

NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT

Бренд: Red Hat Страницы: 74

SocketEthernetIP EN60601

Бренд: Multitech Страницы: 2

Snap Server 18000

Бренд: Adaptec Страницы: 5

Supero SUPERSERVER 5015A-EHF-D525

Бренд: Supero Страницы: 90

MicroCloud 5038ML-H12TRF

Бренд: Supero Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды