Cisco UCS C210 Скачать руководство пользователя страница 95

Страница: 95 / 124

C-3

Cisco UCS C210 Server Installation and Service Guide

OL-20887-02

Appendix

Enabling the Mezzanine Card RAID Controller in the BIOS

When using the supported mezzanine-style RAID controller cards, you must enable the ICH10R
controller in Enhanced mode.

Step 1

Make sure that a RAID cable is attached between the mezzanine card and the disk backplane.

Step 2

Boot the server and press

when prompted to enter the BIOS Setup utility.

Step 3

Select the

Advanced

tab, then

Mass Storage Controllers Configuration

Step 4

Set Onboard SATA Controller to

Enabled

Step 5

Set SATA Mode to

Enhanced

Step 6

Press

F10

to save your changes and exit the utility.

Step 7

To set up a RAID configuration when using the mezzanine card, boot the server and press

Ctrl-C

when

prompted to start the WebBIOS utility.

RAID Controller Cabling

The RAID controller connectors in this server are shown in

Figure C-1

. The blue line indicates the

recommended cable routing path from the backplane to the possible controller locations.

Figure C-1

RAID Controller Connectors

Extender or expander backplane

Mezzanine card connector

Integrated RAID connector on
motherboard

LSI MegaRAID PCIe card connectors

Содержание UCS C210





























































































































Результаты поиска

Содержание UCS C210

Отзывы:

Похожие инструкции для UCS C210

Бренды по названию

Популярные бренды

Cisco UCS C210, Инструкция по установке и обслуживанию

Результаты поиска

Содержание UCS C210

Отзывы:

Похожие инструкции для UCS C210

Бренды по названию

Популярные бренды