Cisco UCS C210 Скачать руководство пользователя страница 115

Страница: 115 / 124

D-15

Cisco UCS C210 Server Installation and Service Guide

OL-20887-02

Appendix

•

Two Cisco Nexus 2248 FEXes.

Note

You must plug a power cord into each of the two power supplies in the FEX. If a power supply
is not connected to power, you might see “Major” faults reported during power-on self test
(POST). For example,

Power supply 1 in fex 6 power: error

. You can clear these errors by

connecting the missing power cord to the FEX power supply.

•

Two RJ-45 Ethernet cables.

•

Four 10-Gb SFP cables.

Upgrade and Connection Procedures

Use the procedures in this section in the following order to upgrade your server and connect it to the
Cisco UCS environment:

Note

These procedures assume that you have already installed the server in your rack and connected it to
power. See

Installing the Server Into a Rack, page 2-4

and

Connecting and Powering On the Server

(Standalone Mode), page 2-9

•

1. Upgrading the Firmware and Rebooting in UCSM Mode, page D-15

•

2. Physically Connecting the Server to the Cisco UCS Environment, page D-17

1. Upgrading the Firmware and Rebooting in UCSM Mode

Step 1

Find the Host Upgrade Utility ISO file download for your server online and download it to a temporary
location on your workstation:

See the following URL:

http://www.cisco.com/cisco/software/navigator.html

Click

Unified Computing and Servers

in the middle column.

Click

Cisco UCS C-Series Rack-Mount Standalone Server Software

in the right-hand column.

Click your model of server in the right-hand column.

Click

Unified Computing System (UCS) Server Firmware

Click the release number that you are downloading.

Note

Release 1.2(2

) is the required level for Cisco UCS Manager 1.4(1x) or 2.0(1x) integration.

Click

Download Now

to download the ISO file.

Verify the information on the next page, then click

Proceed With Download

Continue through the subsequent screens to accept the license agreement and then browse to a
location where you will save the ISO file.

Содержание UCS C210





























































































































Результаты поиска

Содержание UCS C210

Отзывы:

Похожие инструкции для UCS C210

Бренды по названию

Популярные бренды

Cisco UCS C210, Инструкция по установке и обслуживанию

Результаты поиска

Содержание UCS C210

Отзывы:

Похожие инструкции для UCS C210

Бренды по названию

Популярные бренды