Cisco UCS C210 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 124

background image

3-39

Cisco UCS C210 Server Installation and Service Guide

OL-20887-02

Chapter

Replacing a SAS Extender or SAS Expander

This server has two factory-configurable options for hard drive backplane connection: the standard SAS
extender or the optional SAS expander.

Note

The extender and the expander are field-replaceable, but you cannot upgrade an extender to an expander
after-factory.

The SAS Extender

The SAS extender is installed standard in this server.

Figure 3-22

SAS Extender

•

The extender supports connection for up to eight drives. Connector 1 provides connection for drives
1–4, connector 2 provides connection for drives 5–8. See

Supported RAID Controllers and Required

Cables, page C-1

for the required cables.

•

To control more than eight rives, your server must have the optional expander.

The SAS Expander

Note

The SAS expander cannot be used with the onboard ICH10R controller. You must use a RAID controller
card with the SAS expander.

Figure 3-23

SAS Expander

•

The expander supports connection for up to 16 drives when using a single LSI MegaRAID 9261-8i
card. See

Supported RAID Controllers and Required Cables, page C-1

for the required cables.

•

The expander has two mini-SAS SFF-8087 cable connectors. One connector provides connection
for up to 16 drives, and the second connector provides redundancy.

197658

197659

«
...
75
76
77
78
79
...
»

Содержание UCS C210





























































































































Отзывы:

Нет отзывов

Похожие инструкции для UCS C210

Бренд: IBM Страницы: 40

Бренд: Vecow Страницы: 122

Flex System x240 Compute Node

Бренд: IBM Страницы: 28

Бренд: Oki Страницы: 2

Бренд: Obvius Страницы: 29

Бренд: I-O DATA Страницы: 49

Бренд: MSI Страницы: 107

Бренд: Gigabyte Страницы: 115

MediaGrid ContentServer 3000

Бренд: Omneon Страницы: 2

Бренд: Rohde & Schwarz Страницы: 126

PLATINIUM 9000-4R

Бренд: MAXDATA Страницы: 18

Бренд: Lenovo Страницы: 186

42U 1200 mm Deep Dynamic Rack

Бренд: Lenovo Страницы: 42

Бренд: Lenovo Страницы: 32

30131AU - IdeaCentre D400 - 3013

Бренд: Lenovo Страницы: 65

Бренд: Lenovo Страницы: 176

Бренд: Lenovo Страницы: 90

Бренд: Lenovo Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды