Cisco UCS C210 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 124

background image

C-6

Cisco UCS C210 Server Installation and Service Guide

OL-20887-02

Appendix

•

The prompt for the mezzanine-style controller cards is

Ctrl-C

.

•

The prompt for the onboard Intel ICH10R controller utility is

Ctrl-M

.

Note

Cisco has also developed the Cisco Server Configuration Utility for C-Series servers, which can assist
you in setting up some RAID configurations for your drives. This utility is shipped with new servers on
CD. You can also download the ISO from Cisco.com. See the user documentation for this utility at the
following URL:

http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/ucsscu/user/guide/20/SCUUG20.html

LSI MegaRAID Card Beep Codes

Table C-2

contains a summary of the LSI MegaRAID card beep codes. These beep codes indicate

activity and changes from the optimal state of your RAID array. For full documentation on the LSI
MegaRAID cards and the LSI utilities, refer to the LSI documentation for your card.

Restoring RAID Configuration After Replacing a RAID Controller

When you replace a RAID controller, the RAID configuration that is stored in the controller is lost. Use
the following procedure to restore your RAID configuration to your new RAID controller.

Step 1

Replace your RAID controller. See

Replacing a PCIe Card (Mass Storage Controllers), page 3-36

.

Step 2

If this was a full chassis swap, replace all drives into the drive bays, in the same order that they were
installed in the old chassis.

Step 3

If Quiet Boot is enabled, disable it in the system BIOS. See

How to Disable Quiet Boot for CIMC

Firmware Earlier Than Release 1.2(1), page C-5

.

Step 4

Reboot the server and watch for the prompt to press F.

Step 5

Press

F

when you see the following on-screen prompt:

Foreign configuration(s) found on adapter.

Press any key to continue or ‘C’ load the configuration utility,

or ‘F’ to import foreign configuration(s) and continue.

Table C-2

Summary of LSI MegaRAID Card Beep Codes

Beep Code

LSI Firmware State

Cause (Depending on RAID Level)

3 seconds on, 1 second off

SPEAKER_OFFLINE_ENTRY

•

RAID 0: One or more drives offline.

•

RAID 1: Two drives offline.

•

RAID 5: Two or more drives offline.

•

RAID 6: More than two drives offline.

1 second on, 1 second off

SPEAKER_DEGRADED_ENTRY

•

RAID 1: A mirrored drive failed.

•

RAID 5: One drive failed.

•

RAID 6: One or two drives failed.

1 second on, 3 seconds off

SPEAKER_HOTSPARE_ENTRY

A hot spare drive has completed the rebuild process
and has been brought into the array.

«
...
96
97
98
99
100
...
»

Содержание UCS C210





























































































































Отзывы:

Нет отзывов

Похожие инструкции для UCS C210

Бренд: Supero Страницы: 112

Бренд: SMC Sierra Monitor Страницы: 42

Бренд: Data-Tronix Страницы: 29

Бренд: Data-Tronix Страницы: 30

AAEON ARES-WHI0

Бренд: Asus Страницы: 76

Бренд: Asus Страницы: 16

Бренд: Asus Страницы: 42

RS720A-E9-RS24-E

Бренд: Asus Страницы: 162

Бренд: Asus Страницы: 164

TS700-E9 Series

Бренд: Asus Страницы: 178

Бренд: Asus Страницы: 224

Бренд: Asus Страницы: 162

Бренд: Asus Страницы: 196

RS720Q-E9-RS24-S

Бренд: Asus Страницы: 150

TS500-E5 - 0 MB RAM

Бренд: Asus Страницы: 162

Бренд: Asus Страницы: 70

Бренд: Asus Страницы: 146

Бренд: Asus Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды