Christini AWD 450 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 118

background image

Page 18

Maintenance

CHOKE LEVER

CHOKE LEVER

CHOKE LEVER

CHOKE LEVER

FREE PLAY: 2

FREE PLAY: 2

FREE PLAY: 2

FREE PLAY: 2----3mm(1/8

3mm(1/8

3mm(1/8

3mm(1/8 ----3/16in)

3/16in)

3/16in)

3/16in)

•

Check for smooth choke lever operation and lubricate the cable if re-
quired.

•

Inspect the cable for cracks which could allow moisture to enter. Replace
the cable if necessary.

•

Measure the choke lever free play at the lever end. Choke lever free play
can be adjusted at the choke cable. Remove the dust cover from the ad-
juster. Adjust the free play by loosening the lock nut and turning the ad-
juster.

•

Tighten the lock nut. Reinstall the dust cover. Recheck the free play at the
lever.

AIR FILTER

AIR FILTER

AIR FILTER

AIR FILTER

•

Loosen the air cleaner retaining bolt. Remove the air filter.

•

Remove the air filter from the holder.

•

Thoroughly wash the air filter in clean non-flammable or high flash-point
cleaning solvent. Then wash the element again in a solution of hot water
and dishwashing liquid soap. Clean the inside of the air cleaner housing.

•

After cleaning, be sure there is no dirt or sand trapped between the inner
and outer layer of the cleaner. Wash again if necessary.

•

Allow the air cleaner to dry thoroughly. After drying, soak the air filter in
clean Foam Filter Oil or an equivalent.

•

Apply air filter oil to the entire surface of the air filter and rub it with both
hands to saturate the element with oil.

•

Gently squeeze out excess oil. It is important not to over oil or under oil
the element. Apply a thin coat of grease or an equivalent to the sealing
surface.

•

Assemble the air filter and the holder .Slip the air cleaner retaining bolt
through the assembly. Tighten the retaining bolt securely.

NOTICE :

NOTICE :

NOTICE :

NOTICE : If the air filter assembly is not installed correctly ,dirt and dust may
enter the engine resulting in wear of the piston ring and cylinder.

CRANKCASE BREATHER

CRANKCASE BREATHER

CRANKCASE BREATHER

CRANKCASE BREATHER

•

Remove the breather hose drain plug, then drain any fluids or dirt from
the hose into a proper container. Reinstall the drain plug.

«
...
17
18
19
20
21
...
»

Содержание AWD 450























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 450

Soft Luggage Pannier Racks

Бренд: Honda Страницы: 10

Бренд: R&G Страницы: 13

Бренд: SCHUBERTH Страницы: 41

KTM 1190 LED Light Bar

Бренд: CYCLOPS Страницы: 4

Bonneville T100

Бренд: Triumph Страницы: 198

Бренд: Yoshimura Страницы: 4

Бренд: Blata Страницы: 17

Бренд: DYNATEK Страницы: 6

Бренд: BOS Suspension Страницы: 32

Бренд: FMF Страницы: 4

Бренд: Oxford Страницы: 2

Бренд: Petzl Страницы: 14

Бренд: hepco & becker Страницы: 8

Бренд: Abus Страницы: 200

Бренд: Power Riders Страницы: 5

Бренд: 3M Страницы: 77

Бренд: WangYe Страницы: 19

Бренд: MadStad Engineering Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды