Christini AWD 450 Скачать руководство пользователя страница 50

Страница: 50 / 118

Page 49

•

Position the switch so the lever is positioned towards the rider (on)

and slide the housing into the end of the switch.

Note: If there is not enough slack to seat the cable, make sure the
engagement spline is pushed all the way into the gearbox and the bar-
rel adjuster on the cable is turned in completely.

•

Insert the secondary sprocket into the sidebar and make sure it is

fully seated.

•

Position the engagement lever towards the rider (on) and turn the

barrel adjuster out until the eng agement spline just starts to pull
away from the stop snap ring.

•

Push the lever to the off position. Make sure the secondary

sprocket is fully seated. Spin the secondary sprocket to verify that
the spline has fully diseng aged from the sprocket and it spins
freely.

AWD Engagement Installation

Содержание AWD 450























































































































Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды

Christini AWD 450, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды