Christini AWD 450 Скачать руководство пользователя страница 3

Страница: 3 / 118

Page 2

Introduction

Congratulations for making the rig ht choice. The instruction in this book will provide a simple and understandable

guide to your motorcycle’s operation and maintenance.

COMMON NOTICE

Whenever you see the symbols shown below, heed their instructions!

Always follow safe operating and maintenance practices.

If improperly conducted, the sport has the potential to cause environmental problems as well as conflicts with other

people. Responsible use of your motorcycle will ensure that these problems and conflicts do not occur.

TO PROTECT THE FUTURE OF YOUR SPORT, MAKE SURE YOU USE YOUR BIKE LEGALLY, SHOW

CONCERN FOR THE ENVIRONMENT, AND RESPECT THE RIGHTS OF OTHER PEOPLE.

This manual should be considered a permanent part of the motorcycle and should remain with the motorcycle when

resold or otherwise transferred to a new owner or operator.

We reserve the right to amend this motorcycle due to the improvement.

WARNING

This warning symbol identifies special instructions or procedures

which, if not correctly followed, could result in personal injury, or loss

of live.

CAUTION

This caution symbol identifies special instructions or proce-
dures

which, if not strictly observed, could result in damage to or de-
struction of equipment.

NOTE

This note symbol indicates points of particular interest for more

efficient and convenient operation.

Содержание AWD 450























































































































Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды

Christini AWD 450, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды