Christini AWD 450 Скачать руководство пользователя страница 30

Страница: 30 / 118

Page 29

Maintenance

DRIVE CHAIN SLIDERS

Chain slider

•

In sp e ct t h e d r i v e ch a i n sl i d e r f o r e x ce ssi v e w e a r .

Service li mit:5.0mm from upper surface

Notice:

If the chain slider becomes worn though to the swingarm, the chain will wear
against the swingarm.

•

check the chain guide and chain guide slider for alignment, wear or dam-
aged.

•

Replace the chain guide if it is damaged or worn.

•

Replace the chain guide slider if the chain is visible through the wear in-
spection window.

DRIVE CHAIN ROLLER

Inspect the drive chain roller for excessive wear or binding.

Service li mit:

Mini mum roller O.D: Upper: 39mm/Lower: 35mm

•

Replace the roller if necessary, and tighten the roller bolt/nut to the

specified torque.

(The sign”

means installing the drive chain roller outside)

Torque:Upper bolt: 12N.m

Lower nut: 12N.m

DRIVE/DRIVEN SPROCKETS

•

Inspect the drive and driven sprocket teeth for wear or damage and re-
place if necessary.

Do not install the new drive chain on worn sprocket. The chain and sprockets
must be in good condition, or the new chain will wear rapidly.

•

Inspect the bolts and nuts on the drive and driven sprockets.

•

Tighten them when they become loosened.

Torque:

Drive sprocket bolt:

31N.m

Driven sprocket nut: 32N .m

Содержание AWD 450























































































































Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды

Christini AWD 450, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды