Christini AWD 450 Скачать руководство пользователя страница 20

Страница: 20 / 118

Page 19

Maintenance

SPARK PLUG

REMOVAL

•

Remove the fuel tank and disconnect the spark plug cap. Remove The
spark plug and inspect it for damage

•

Clean around the spark plug base with compressed air before removing
and be sure that no debris is allowed to enter the combustion chamber.

INSPECTION

•

Check the following and replace if necessary:

1. ·insulator for damage

2. ·electrodes for wear

3. ·burnt or discoloration

•

If the electrode is contaminated with accumulated debris or dirt replace
the spark plug.

(this motorcycle’s spark plug is equipped with an iridium center electrode. Re-
place the spark plug if the electrode is contaminated.)

•

Replace the plug if the center electrode is rounded as shown in the pic-
ture.

(Always use the specified spark plugs on this motorcycle)

RECOMMENDED SPARK PLUG (OR EQUIVALENT)

Standard

Standard: DENSO: IK24

DENSO: IK24

Optional : DENSO: IK27

Check the gap between the center and side electrodes with a wire

Type feeler gauge

(To prevent damaging the iridium center electrode, use a wire type

Feeler gauge to check the spark plug gap. Do not adjust the spark

Plug gap if the gap is out of specification , replace with a new one.)

Spark plug gap: 0.4mm

Make sure that the 1mm diameter plug gauge does not insert between the
gap.

If the gauge can be inserted into the gap , replace the plug with a new one.

INS TALL

•

Reinstall the spark plug into the cylinder head and hand tighten , then
torque to specification.

Torque: 22N .m(2.2kgf.m,16lbf.ft)

Содержание AWD 450























































































































Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды

Christini AWD 450, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды