Christini AWD 450 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 118

background image

Page 66

•

Install cover bearing into cover with bearing installation tools.

•

Install internal and external cover 0-rings. Note:

Note:

Note:

Note: all 0-rings should

be lightly coated with grease before being reassembled.

•

Insert drive carrier o-ring on drive carrier and insert drive carrier
into cover and tap into place. Note:

Note:

Note:

Note: face of drive carrier should be

flush with cover bearing and machined cover surface.

•

Place drive insert on tooth side of bevel gear and line up all four
threaded holes with clearance holes on gear.

•

Set cover and drive carrier on top of bevel gear assembly, with
smooth side of gear facing the cover.  Line up 4 bolt holes  and
thread drive carrier bolts into drive insert.  Blue Loctite should be
used on bolts.  Final tightening of bolts will require a square bar or
soft jaws to keep gear from spinning.  Torque bolts to 8ft ft-lbs.

•

Check that bevel gear spins freely on cover.  If it does not spin
freely, check to make sure all o-rings and the cover bearing are
properly seated.  If new o-rings are used, there may be more
friction until o-rings seat and break in.

•

Insert axle o-ring into drive carrier.

Dropout Service

«
...
65
66
67
68
69
...
»

Содержание AWD 450























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 450

Бренд: Fantic Motor Страницы: 130

Бренд: yasuni Страницы: 11

B-TRK502-02-01-SL

Бренд: SRC Страницы: 4

Бренд: Sym Страницы: 31

Body Protector 4.5 Junior

Бренд: Leatt Страницы: 40

Бренд: Memphis Shades Страницы: 2

Бренд: BMW Motorrad Страницы: 261

Бренд: Honda Страницы: 190

MASTERFOX 125cc 2015

Бренд: d'Magna Страницы: 29

Бренд: rizoma Страницы: 14

Бренд: Denali Страницы: 2

Бренд: R&G Страницы: 13

Бренд: RDMOTO Страницы: 3

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 7

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды