Christini AWD 450 Скачать руководство пользователя страница 23

Страница: 23 / 118

Page 22

Maintenance

IN TAKE VALVE:

•

Insert the feeler gauge between the valve lifter and the cam labe.

•

Check the valve clearance for the intake valves using a feeler gauge.

Valve clearance IN: 0.16

Valve clearance IN: 0.16+

+ 0.03mm

0.03mm

EXHAUST VALVE:

•

Insert the feeler gauge between the rocker arm and shim.

•

Check the valve clearance for the exhaust valves using a feeler gauge.

Valve clearance Ex: 0.28

Valve clearance Ex: 0.28+

+0.03mm

0.03mm

VALVE CLEANCE ADJUS TMENT:

•

Remove the camshaft holder assembly

•

The shims my stick to the inside of the valve lifter.

•

Do not allow the shims to fall into the crankcase.

•

The shims can be easily removed with tweezers or a magnet.

•

Clean the valve shim contact area in the valve lifter with compressed air.

•

Measure the shim thickness and record it.

Содержание AWD 450























































































































Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды

Christini AWD 450, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды