Christini AWD 450 Скачать руководство пользователя страница 28

Страница: 28 / 118

Page 27

Maintenance

TRANSMISSION OIL

CHECKING OIL

•

Run the engine at Idle for 3minutes, turn off engine and wait 3 minutes.

•

Support the motorcycle on a level surface and remove the transmission oil
filler cap, engine check bolt and sealing washer from the right crankcase
cover. A small amount of oil should flow out of the check bolt hole.

•

If no oil flow out, fill with recommended transmission oil through fueling
hole until it can flow out of the hole.

•

Reinstall the oil check bolt and engine oil filler cap. Repeat steps above

•

After checking the oil level or filling, install the oil check bolt with a new
sealing washer, tighten the oil check bolt and oil filler cap.

CHANGING ENGINE OIL

•

Run the engine to let it get hot before draining oil.

•

Support the motorcycle in an upright position on a level surface and re-
move the engine oil filler cap from the right crankcase cover

•

Place an oil drain pan under the engine to catch the oil. Then remove the
drain bolt and sealing washer.

•

After the oil has drained, install the drain bolt with a new sealing bolt to
the specified torque

Torque: 22N .M

•

Fill the recommend oil to the engine.

Recommended transmission oil: APLGL

Viscosity: SAE80W_90

Capacity: 0.65 liter at draining

0.75 liter at removing

•

Inspect the oil level as the steps of oil level checking procedure.

Содержание AWD 450























































































































Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды

Christini AWD 450, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450

Отзывы:

Похожие инструкции для AWD 450

Бренды по названию

Популярные бренды