CD3 Outpost Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 56

CD3 Outpost Скачать руководство пользователя страница 52

CD3 Products Manual

CD3, General Benefit Corporation |

www.cd3station.com

|

[email protected]

| 612.467.9441

Patent

Pending | Made in USA | © 2019

52

5.3.5 Vacuum

The vacuum motor operates on 24VDC power which is sent from a relay on the main
electrical panel. This relay is actuated by an output from the control module and
dictated by the programming and associated lighted button input. There is also a float
switch inside the top of the vacuum tank that stops its function if the tank is completely
full.

5.3.6 Lights

The lights operate on 12VDC power from a relay on the main electrical panel. The signal
from the associated lighted button is 24VDC, but supplied in 12V to the relay.

5.4 Outpost

5.4.1 Battery Pack

The Outpost system is powered by a 24VDC battery pack that powers the system directly and
the power is supplied to the system through the solar panels is 24VDC as well. The panels are
12VDC output individually, but wired in series to obtain the desired voltage. The panels charge
the system through the solar charger which is found on the main electrical panel inside the unit.

5.4.2 Solar Panels/Solar Charging

The Outpost unit utilizes solar panels to provide a charge voltage as long as they have
light provided to them.  The panels themselves are each operating in the range of 12V
and are wired in series to increase their collective voltage output to match the system.
Amount of light and shade on the panels is critical in that, if there is one entire cell of
one panel covered or shaded, neither panel will not output power.  The panels charge
the battery pack through the solar charge controller which is a buck type charger.  The
solar charge controller will only allow charge to the battery pack as long as the voltage
input from the panels are higher than the battery pack voltage.

5.4.3 Light

The light operates on 24VDC power from a relay bound to the wiring harness just below
the electrical panel. The signal from the associated lighted button is also 24VDC.

«
...
50
51
52
53
54
...
»

Содержание Outpost

























































Отзывы:

Нет отзывов