CD3 Outpost Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 56

CD3 Outpost Скачать руководство пользователя страница 36

CD3 Products Manual

CD3, General Benefit Corporation |

www.cd3station.com

|

[email protected]

| 612.467.9441

Patent

Pending | Made in USA | © 2019

36

4.2 Blower/Compressor (Station/Wayside Only)

4.2.1 Blower/Compressor Maintenance Safety

**Important! - Always disconnect power from the system using the main power
shut-off switch and relieve all air pressure from the system prior to servicing.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY WHILE SERVICING:

1.

The air produced by this unit is not fit for human or animal consumption and it must not
be used to provide a breathing air supply.

2.

The compressor is designed for use in the compression of normal atmospheric air only.
No other gases, vapors or fumes should be exposed to the compressor intake, nor
processed through the compressor.

3.

Make sure to disconnect all power supplies to the unit prior to any service on the
compressor/blower system.

4.

Relieve all pressure internal to the compressor or blower system prior to servicing. Do
not depend on any check valves to hold system pressure.

5.

Do not change the pressure setting on the safety relief valve, restrict the function of the
safety relief valve, or replace the safety relief with a plug. Over pressurization of some
system or compressor components can occur, resulting in sever personal injury, death
and property damage.

6.

Do not modify the system to dispense air at any pressure exceeding 90 PSI.

7.

Never use flammable or toxic solvents for cleaning the air filter or any parts.

8.

Do not attempt to service any part while the compressor is operating.

9.

Do not operate the compressor at any pressures in excess or its rating.

10.

Do not operate with the shrouds or belt guard removed.

11.

Follow all maintenance procedures and check all safety devices on schedule.

12.

Use the correct lubricants at all times.

13.

High temperatures are generated by the pump and manifold.  To prevent burns or other
injuries, do not touch the pump, manifold or transfer tube while the pump is running.
Allow them to cool before handling or servicing.

14.

Keep children away from the compressor at all times.

15.

Always wear hearing protection when using an air compressor. Failure to do so may
result in hearing loss.

«
...
34
35
36
37
38
...
»

Содержание Outpost

























































Отзывы:

Нет отзывов