CD3 Outpost Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 56

CD3 Outpost Скачать руководство пользователя страница 18

CD3 Products Manual

CD3, General Benefit Corporation |

www.cd3station.com

|

[email protected]

| 612.467.9441

Patent

Pending | Made in USA | © 2019

18

3.3 Vacuum System (Station/Wayside Only)

3.3.1 Vacuum Intended Use

The vacuum is intended for wet and dry operation.  It is meant to clean debris from a
watercraft and/or watercraft trailer of all types on the inside or outside.  Any organic
debris can be removed with the vacuum.  Please place inorganic material in the
appropriate trash containers.  The vacuum is intended for plant life, such as lake weeds,
as well as animal life, such as unwanted fishing bait. The vacuum can be used to remove
the water as well as the bait from the container.  The vacuum is also intended to
remove any water from a watercraft in any location.

3.3.2 Vacuum Safety Information

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1.

Do not allow vacuum to operate if hose is blocked. If air is not permitted to flow
through the vacuum motor while running, motor damage may occur.

2.

Do not block the exhaust air from the vacuum or restrict it as motor damage may
occur.

3.

Do not use the vacuum to pick up anything that is burning or smoking, such as
cigarettes, matches or hot ashes.

4.

Do not use the vacuum to pick up flammable or combustible liquids such as gasoline
or use in areas where they may be present.

5.

Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such
as asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangering
materials. Specially designed units are available for these purposes (this unit is not
one of them).

6.

Do not pick up soot, cement, plaster, or drywall dust. These are very fine particles
that may pass through the system and affect the performance of the motor or be
exhausted back into the air.

7.

The operation of a vacuum can result in foreign objects being blown into eyes, which
can result in eye damage. Always wear eye protection when operating the vacuum.

8.

STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum
when you are tired, distracted or under the influence of drugs, alcohol or medication
causing diminished control.

«
...
16
17
18
19
20
...
»

Содержание Outpost

























































Отзывы:

Нет отзывов