CD3 Outpost Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 56

CD3 Outpost Скачать руководство пользователя страница 28

CD3 Products Manual

CD3, General Benefit Corporation |

www.cd3station.com

|

[email protected]

| 612.467.9441

Patent

Pending | Made in USA | © 2019

28

8.

Always operate equipment in a position to provide maximum visibility at all times. Make
allowances for increased length and weight of the equipment when making turns,
stopping the unit, etc.

9.

Be extra careful when working on inclines.

10.

Avoid loose fill, rocks and holes; they can be dangerous for equipment operation or
movement.

11.

Operate the towing vehicle from the operator’s seat only.

12.

As a precaution, always recheck the hardware on equipment following each and every
use. Correct all problems. Follow the maintenance safety procedures.

3.7.2.5 After Operation Safety

1.

Store the unit in an area away from human activity.

2.

Do not permit children to play on or around the stored unit.

3.

Make sure all parked machines are on a hard, level surface and engage all safety
devices.

4.

Wheel chocks may be needed to prevent unit from rolling.

3.7.3 Trailer Lowering/Crank Down Procedure

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE SERIOUS BODILY INJURY
AND/OR DAMAGE TO THE UNIT/TRAILER.

Danger – Keep hands and feet clear of the trailer frame when lowering.

Danger – DO NOT lean over the leaf spring while raising or lowering the trailer, stand
behind the winch.

The trailer can be lowered to the ground using the 3 cranks/winches. There is one
crank/winch located behind each wheel as well as one behind the tongue jack. There
are also leveling jacks at each corner of the trailer. Begin the process by setting the
leveling jacks at the desired height for the trailer position once it has been lowered.
Each leveling jack using a clevis pin with a locking cotter pin. Make sure all the locking
cotter pins are in place on the leveling legs prior to lowering the unit.

Begin the lowering process at the front crank/winch located behind the tongue jack.
The cotter pin and clevis pin must be removed first. The clevis pin might require the
crank/winch to be raised slightly to relieve pressure from the clevis pin so that it can be
removed easily. Change back and forth between cranking up and down using the

«
...
26
27
28
29
30
...
»

Содержание Outpost

























































Отзывы:

Нет отзывов