Carver 42 SUPER SPORT Скачать руководство пользователя

Страница: 48 / 141

4127 • 42 Super Sport 4/06

AC ELECTRICAL SYSTEM

SECTION 3

To connect to shore power:

Do not supply power to a boat that has not had its water system fully

charged. Doing so will damage the unit’s water heater.

1. Make sure the generator is not running.

2. On the AC Control Center, located in a cabinet in the aft starboard side

of the salon, switch the Water Heater circuit breaker “OFF.” Do not switch

the breaker on again until the fresh water system has been ﬁlled, pressurized

and primed.

3. Also on the AC Control Center, switch the Shore 1 and Shore 2 circuit

breaker groups “OFF.”

4. Switch “OFF” the AC Main circuit breaker groups. These circuit breaker

groups are located in the port transom locker on the boarding platform.

Make sure the shore power cord(s) you use is in excellent condition

with no cuts, nicks or abrasions in the exterior plastic cover. Also

make sure that the cord(s) is speciﬁcally designed to connect your boat

to a shore power source. Using a damaged cord or a cord that is not

designed for this purpose can cause electrical shock resulting in death

or serious injury.

5. Locate your 50' shore power cord(s). If you are connecting the optional

Cablemaster, proceed to step 8.

6. Connect the female end of the cord(s) to the boat’s shore power

receptacle(s). The receptacle(s) are located in the port transom locker

on the boarding platform.

7. Secure the nonmetallic threaded locking ring that locks each cord to

the boat’s shore power receptacle. This prevents the cord(s) from being

accidentally disconnected and from arcing due to a gap between the cord

plug and the receptacle.

Do not allow the end of the shore power cord(s) to hang in the water. This

can cause an electrical ﬁeld to form which can kill or seriously injure

nearby swimmers or passengers.

8. Choose a neat and safe way to route the shore power cord(s) to the shore

power source box.

9. Switch the circuit breaker that is installed in the shore power source

box “OFF.”

10. Plug the male end of the shore power cord(s) into the shore power

source outlet.

Содержание 42 SUPER SPORT














































































































































Результаты поиска

Содержание 42 SUPER SPORT

Отзывы:

Похожие инструкции для 42 SUPER SPORT

Бренды по названию

Популярные бренды

Carver 42 SUPER SPORT, Руководство пользователя

Результаты поиска

Содержание 42 SUPER SPORT

Отзывы:

Похожие инструкции для 42 SUPER SPORT

Бренды по названию

Популярные бренды